Wow... Pretty bad when "The Best Woman Dress Up Socks" has more views than my post... ...   Thu Mar 5th, 2020 09:37 pm

I got the whole kart disassembled now, and I'm about to start cleaning the paint off the kart. I was thinking of using a wire ...   Mon Mar 2nd, 2020 12:39 am

Hey Rick, isn't the Concept the one that I was following at Kershaw to make sure you made it back to the pits when you ...   Thu Feb 27th, 2020 08:36 pm

BTW everyone, this was meant as a joke... ...   Fri Feb 21st, 2020 10:14 am

New Kart shop, figured I would give them a try, went in, asked to get a wheel half, and this is what they brought out... ...   Wed Feb 19th, 2020 08:53 pm

Thanks for the pipe ID Tom! I saw a picture of one once, but I wasn't sure if that was what it was or not. ...   Tue Feb 18th, 2020 09:41 pm

Ok, another question I have... What did K&P use as their "standard" sprocket? Was it the Tru-A-Line setup or the Hegar Quick Change setup? Figure ...   Mon Feb 17th, 2020 05:58 pm

PM Sent Richie ...   Thu Feb 13th, 2020 12:16 am

Ok, thanks to really old parts and small stamped letters, I found out that these are actually HL194C carbs... Sorry about the confusion. Guess I ...   Tue Feb 11th, 2020 06:18 pm

Hey Barry, I checked and I could not find anything except for a few PTO side adapters, nothing for the flywheel side, sorry about that. ...   Tue Feb 11th, 2020 12:38 pm

Not sure if I have anything like that in the footlocker, but I'll take a gander tomorrow morning before I head to work and let ...   Tue Feb 11th, 2020 01:40 am

Finally got a really bad picture with my phone of the kart to post on here, this is just after I got it home and ...   Tue Feb 11th, 2020 01:37 am

Hey Barry, are you talking about a starter cup to use a fan belt, or an actual starter nut? Think I have a starter cup ...   Tue Feb 11th, 2020 01:34 am

Looking for either a set of Hartman Axle Clutch shoes or the linings to put on the set I have. ...   Mon Feb 10th, 2020 08:51 pm

Got two HL184C Tillys on the Mac motor, they have the double pumper on them and a 1" bore, but I am trying to find ...   Wed Feb 5th, 2020 10:00 pm

Going to be running a slippy pipe and a Horstman axle clutch to start off with, kind of afraid to run the Hartman axle clutch ...   Wed Feb 5th, 2020 05:46 pm

LOL! It was in a barn next to a pasture when I got it originally up in Maryland, the guy I got it from ran ...   Wed Feb 5th, 2020 12:27 pm

Figure I'd post a picture of my Coyote ...   Tue Feb 4th, 2020 05:38 pm

Picture #4 ...   Mon Feb 3rd, 2020 08:39 pm

Picture #3 ...   Mon Feb 3rd, 2020 08:38 pm

Picture #2 ...   Mon Feb 3rd, 2020 08:38 pm

Pictures of the Mac, picture #1 ...   Mon Feb 3rd, 2020 08:38 pm

Ok, turns out I do have another question on the Stinger. Trying to figure out if the pitman arms on the steering shaft are suppose ...   Mon Feb 3rd, 2020 08:07 pm

I just picked up a Bug Stinger, kart and all the parts was rolled into a garage in 1972, and been there since. Just got ...   Sat Feb 1st, 2020 10:07 pm

I'm also into the laydown karts, I have a 75 Coyote Enduro (the Red Devil copy) with a K88. Planning on being at Charlotte with ...   Sat Feb 1st, 2020 09:47 pm