Bert, On my kart there are no welded on tabs or anything like that to hold the brake lines. Originally there might have been some ...   Tue Dec 5th, 2017 09:27 pm

Bert, Let me know what it is you want to see and I'll post pics...............after I'm done plowing the fields,slapping the hogs,ect http://yoursmiles.org/msmile/animal/m02107.gif ...   Tue Dec 5th, 2017 01:26 am

Doug, Yes I turned down a piece of solid round stock on my lathe and pressed it into the side rails. The bearing hangers and ...   Thu Sep 21st, 2017 11:46 pm

Andy Simon picked up his Rupp tonight after I installed a new rear clip when the orig one broke off at the seat back supports. ...   Thu Sep 21st, 2017 02:11 am

ORIG POST EDITED ...   Tue Sep 12th, 2017 02:36 am

Scott,Yea Barry's fine...........I can tekk he's fine because he's still grumpy :) ...   Sat Sep 9th, 2017 08:22 pm

Larry,I feel your pain and am still in disbelief as you & I just talked about Chris Yesterday and in fact he sent me a ...   Thu Sep 7th, 2017 09:28 pm

Back together this morning now gotta go show up at work for a couple hours then I'll put the motor back on & do the ...   Thu Sep 7th, 2017 02:51 pm

The flip http://s260.photobucket.com/user/modified32/slideshow/Barrys%20flip ...   Wed Sep 6th, 2017 09:51 pm

Now Doug you know better...................this is just a fraction of my "kids" :) ...   Wed Sep 6th, 2017 08:33 pm

Hi Tom,Let's just say a new driver at Oreville can be thankful that Barry's years of driving experience avoided a hard t-bone hit to him ...   Wed Sep 6th, 2017 01:50 am

Spent the day today replacing the front axle on one of my Foxes. Almost got this act down to under an hour thanks to having ...   Tue Sep 5th, 2017 02:11 am

Offering the following karts: PM or email me a80luv@yahoo.com Karts are located in NE Pa 18080 Margay #C H/A ...   Mon Sep 4th, 2017 12:15 am

Bill,Photobucket already has you covered.If you look to the lower right of the screen you will see where you can change the speed of the ...   Sun Sep 3rd, 2017 11:08 pm

Barry Greenzweig wrote: You have to sell em to fix my fox? I keep tellin ya Barry...........there is nothing wrong with that kart................the percentages look just ...   Sun Sep 3rd, 2017 10:02 pm

Bill,there's a link (in blue letters)in my post that takes you to a slideshow of the motors on Photobucket. There's info captions above the pics ...   Sun Sep 3rd, 2017 09:43 pm

MOTORS HAVE BEEN SOLD,THANKS! http://i260.photobucket.com/albums/ii19/modified32/McCulloch%20motors%20for%20sale/mac%20motors%20132%20-%20Copy_zpsir1xms0m.jpg ...   Sun Sep 3rd, 2017 07:51 pm

Hey Dan,How are ya! Thanks for the quick reply. From what I could tell the studs broke but the cylinder also received damage at ...   Sun Aug 27th, 2017 11:48 pm

Looking for a cylinder,piston & rings and a connecting rod for a Power Products AH-61 or a complete motor for a guy who showed up ...   Sun Aug 27th, 2017 11:00 pm

Ken,no progress to report on the Red Devil as I haven't had the time as keeping my 4 Foxes race ready every week plus helping ...   Sat Aug 5th, 2017 01:53 am

Chuck,I lost alot of my pics too when my old pc became a vegetable so these are all I have. Your side plates are definitely ...   Sun Jul 9th, 2017 01:16 am

Chuck,Can you get a better pic of the rear area? Your side plates where the rear axle mounts looks bigger then the ones on my ...   Sat Jul 8th, 2017 10:53 pm

Ken,Yes the washers are actually thrust washers but unlike the Torrington ones these just have the appearance of being a brass washer. Looking forward ...   Sun Jul 2nd, 2017 03:06 pm

Dan,Thanks for posting that pic. I'm suprised to see they list the sprint as coming with Azusa wheels.I would imagine they would have been the ...   Sat Jul 1st, 2017 05:52 pm

Hi Ken, Yes and no,lol I did manage to install the front tie rods and rear axle & sprocket BUT after looking at the pic ...   Sat Jul 1st, 2017 04:06 pm

Scott,I'll keep ya informed for sure. Worst case if it becomes a total failure I can still just display it on a stand because it ...   Sat Jul 1st, 2017 01:25 pm

Scott,That's a great story as to what these blowers were used for and considering the fact we're talking about our military,I completely believe it! :) ...   Fri Jun 30th, 2017 08:32 pm

Barry,you mean those motors should last longer then 8 laps? 😳 I would have never guessed! ...   Tue Jun 20th, 2017 03:46 pm

Dean, From the info I could find on the internet it seems like this blower was made for the military in the early 60's for ...   Tue Jun 20th, 2017 01:49 am

Dean, I actually found a small McCulloch screw type blower that was made in the 60's that I'm going to use on one of my ...   Mon Jun 19th, 2017 01:07 am

Got this reply from Ken Northside via a pm as he is having a problem signing on.Thanks for the info Ken. Carl I have the same ...   Tue Jun 13th, 2017 08:26 pm

Doug,You are correct on the angles of the upper and lower frame rails being different in the pics. In the photos where the frame is ...   Tue Jun 13th, 2017 10:34 am

Finally had two whole days without rain here in PA so I managed to get some color on my newest Red Devil and begin assembling ...   Mon Jun 12th, 2017 02:05 am

Doug,Got ya covered if you need a manifold...........should I MAIL it to ya? http://www.sherv.net/cm/emoticons/yellow-hd/embarrassed-smile-smiley-emoticon.gif http://i260.photobucket.com/albums/ii19/modified32/parts/024_zpsgeltpzmg.jpg ...   Mon Jun 5th, 2017 08:53 pm

Chuck,if I put the GoPro on Alex all you'd see is a empty track........................until he comes around again to lap us! http://www.sherv.net/cm/emo/laughing/giggling.gif ...   Mon Jun 5th, 2017 08:43 pm

A couple of our vintage kart drivers came out to Oreville today to run and try to beat the rain and it was a great ...   Mon Jun 5th, 2017 02:44 am

Pics as Barry is very very busy building a motor for me ;);)......or at least he should be! Serial number is hard to see in ...   Mon May 29th, 2017 06:30 pm

Hi Dan,glad you remembered I was interested in it,yes I want it,check your pm's. Carl ...   Mon May 15th, 2017 01:59 pm

Pm sent ...   Mon Apr 10th, 2017 09:42 pm