2: ...   Sun Sep 11th, 2022 05:17 pm

Cam lobe location on cranks: ...   Sun Sep 11th, 2022 05:16 pm

Here's a visual aid:LH flywheel on left, RH flywheel on right. ...   Sun Sep 11th, 2022 05:07 pm

What's the consensus: Nitrile or Teflon? ...   Mon Jul 26th, 2021 01:03 pm

Looking for Dyna-Drive gear sets in the 6.0 to 6.8 range. Will buy outright or can trade other ratios that I have. ...   Thu Jul 22nd, 2021 12:54 am

Looks like a '63 Fox 2200 which was a box mount version of the '62 Fox Go-Boy kart (which had swing mounts). This was also ...   Sun Jun 20th, 2021 01:49 pm

Never mind, I think I figured it out. ...   Fri Jun 18th, 2021 09:49 pm

Your picture is of an AH82. Are you looking for a left hand AH58 or a left hand AH82? ...   Tue May 25th, 2021 01:22 pm

I haven't found an IPL, but Discount Marine is pretty confident that their kit for the Brown Model 15-CP carb would fit the KA1000 also. ...   Sun May 23rd, 2021 04:58 pm

Looking for a Power Products AH61 LH stroker crankshaft (part #290317). FOUND ONE ...   Wed May 5th, 2021 09:24 pm

I have the December 1963 issue of Karting World that featured a test of the Shoemaker "siamesed" West Bends. I don't see any starter pulleys ...   Wed Mar 24th, 2021 10:09 pm

Flywheel magnet polarity orientation makes no difference on a point/condenser ignition system. That's why West Bend only listed one flywheel (Y13294) for both their RH ...   Sun Mar 7th, 2021 11:59 am

pm sent ...   Wed Feb 24th, 2021 10:21 pm

Anyone have a parts breakdown for the Brown KA1000 alky carb? ...   Tue Feb 23rd, 2021 01:32 pm

Flywheels are the same for RH/LH West Bend and Chrysler 610/820's (with point/condenser). They may be handed on the US Marine and US Motor Power ...   Fri Feb 19th, 2021 02:50 pm

The tooth shape is also different than those on the DynaDrive gears (more involuted). They all are machined for the McCulloch taper. ...   Thu Feb 4th, 2021 11:34 pm

Dyna-Drive gearbox gears have the ratio (4.00-1, 5.88-1, etc) stamped on the primary and intermediate gears. I came across a bunch of primary gears that ...   Sat Jan 23rd, 2021 05:58 pm

Okay. The welds look too good and consistent (kind of like those on the factory 580 weighted cranks) not to be factory, but could be ...   Thu Jan 21st, 2021 02:09 pm

I came across some WB 610/820 cranks while cleaning. 2 of them have weights welded on, the others don't. I assume the ones with the ...   Thu Jan 21st, 2021 01:04 am

I have a 4.0 without a tin or there's one on ebay complete with tin. ...   Sat Jan 2nd, 2021 06:06 pm

I still have the '62 Mak. The '59 is long gone...except for the rod ends. We changed the steering on the '59 back then to ...   Sat Nov 7th, 2020 09:19 pm

Here's three of the ones that were on our '59 Mak which we bought in '60 and one off my '62 which I bought at ...   Sat Nov 7th, 2020 05:26 pm

Hey Dick, What year Foxes did the pictured ones come from? My '59 and '62 Maks both came with rod ends that were more elongated. I'm ...   Sat Nov 7th, 2020 01:36 am

CEV #6310 ignition coil for sale. This is the 6V AC black plastic encapsulated dry coil used on the Parilla BA-13 and early, pre-motoplat Komets ...   Thu Oct 22nd, 2020 02:42 pm

and another ...   Mon Aug 10th, 2020 01:51 pm

here's one ...   Mon Aug 10th, 2020 01:50 pm

1 ...   Mon Jul 13th, 2020 05:49 pm

Anyone have a King Kart pyramidal aluminum floor tank? Need some dimensions. ...   Sat Jul 11th, 2020 03:19 pm

From 1961 GK Brochure: Model 801 Single Clinton A490 $219.00 Model 802 Dual Clinton A490 $259.00 Model 803 Single West Bend 580 $295.00 Model 804 Dual West Bend 580 ...   Wed May 27th, 2020 12:47 am

GK800 ...   Wed May 27th, 2020 12:28 am

Looks like a Continental 1/4 midget engine, AU7R maybe. ...   Thu Mar 19th, 2020 01:58 pm

West Bend 580 inner shroud for LH (left side) engine. I have 2. Bearings and seals appear to have been replaced and stuffing added. Good ...   Fri Mar 13th, 2020 12:06 am

That's the later style. The early style looked like this: ...   Tue Nov 26th, 2019 09:35 pm

I know Dick Teal was making these a few years ago, is anyone making them now? Just asking before I splurge on a tube bender. ...   Sun Nov 24th, 2019 10:34 pm

I'm looking for an early PP58 angled air filter base. I have the filter(s), just need the base. If you're "early", you know what it ...   Sun Nov 24th, 2019 09:29 pm

another pic ...   Sun Nov 17th, 2019 10:58 pm

I was going through some old parts boxes and came upon this. Does anyone remember who made it? I was thinking Mercury (the clutch people) ...   Sun Nov 17th, 2019 10:55 pm

rod ends: ...   Tue Oct 1st, 2019 12:23 am

The GP I used to have had the rivets 3" o.c. on most of floor pan but 1 1/2" o.c. under seat area. 1/8" steel ...   Fri Sep 27th, 2019 03:42 am

It wouldn't handle very well as-is (looks like about a 10"+ stretch). Lots of work but, if you have the the time and are a ...   Tue Sep 10th, 2019 01:19 pm